0
1/4" x 3-1/4" S.S., Toggle Jaw x Hand Swage Turnbuckle for 3/16" Cable Image 1
1/4" x 3-1/4" S.S., Toggle Jaw x Hand Swage Turnbuckle for 3/16" Cable Image 4
1/4" x 3-1/4" S.S., Toggle Jaw x Hand Swage Turnbuckle for 3/16" Cable
1/4" x 3-1/4" S.S., Toggle Jaw x Hand Swage Turnbuckle for 3/16" Cable
1/4" x 3-1/4" S.S., Toggle Jaw x Hand Swage Turnbuckle for 3/16" Cable
Open in new window
1/4" x 3-1/4" S.S., Toggle Jaw x Hand Swage Turnbuckle for 3/16" Cable

1/4" x 3-1/4" S.S., Toggle Jaw x Hand Swage Turnbuckle for 3/16" Cable

review 0 Review(s) 0 0 5 Review this item
0 Questions
$19.95

InStock

SHIPS TODAY In Stock

Qty.
Product Specs Part No. 51626210
Material Type 316 Stainless Steel
Weight 0.25 lb

Description

Toggle Jaw x Hand Swage Turnbuckle, Pipe Style - 1/4 inch x 3-1/4 inch size for 3/16 inch cable, Stainless Steel, Grade 316.

Spec Sheet
quarter-inch-x-three-and-one-quarter-inch-stainless-steel-toggle-jaw-swage-turnbuckle-three-sixteenths-inch-cable-specification-diagram
NameValue
Stud Outside Diameter (A):1/4 inches
Take-Up (B):3-1/4 inches
Cable Size (C):3/16 inches
Inside Jaw Length (D):1 inches
Inside Jaw Width (E):0.4 inches
Before Swage Diameter (F):0.292-0.297 inches
After Swage Diameter:0.245-0.25 inches
Pin Diameter (P):0.2 inches
Closed Length (L):7 inches
Special Instructions

Cable Railing Hand Swage Instructions

(View PDF)

Hand swage fittings using hand swage tool installation instruction.

FAILURE WILL RESULT IF YOU DO NOT USE THE PROPER TOOLS.

You will require the following tools for hand swage fittings ins:

  • Wire rope cutter
  • Hand Swage Tool, 22-ST20 for 1/8", 3/16" wire, 22-ST22 for 1/4" wire.
  • Marker

Note: Use only 1/8" or 3/16" preformed, corrosion resistant wire in 1x19, or 7x7 construction only.

Step:

  1. Measure and mark the desired length on the cable with the marker and cut the cable to your length.
  2. Place the fitting on the proper cavity on the tool. 22-ST20 for 1/8" and 3/16" cable and 22-ST22 for 1/4" cable.
  3. Insert the cable into the terminal and place the terminal approximately 1/8" from end in the die.
  4. Complete three crimps as shown in the drawing. Each crimp should be 1/8" in between crimps, rotate the fitting 180 degrees between each crimp.
  5. Use a gauge (not included) to check the after crimp dimension. Make sure to rotate the terminal to measure the smallest part of the swage.

Adjust the bolt on the tool if necessary to get a proper after swage dimension.

Hand swage fittings will withstand pullout strains of 60% if applied properly. WE DO NOT WARRANT USE OF THESE TERMINALS FOR STRANDING RIGGING OR OTHER HIGH LOAD APPLICATIONS.

Hand Swage Tool Diagram
Note:
Size
1/4 inches
Length
3-1/4 inches
Certificates
Product Type
stainless > fittings > turnbuckles
Customer Reviews
[rating] Stars
[short_review]
[long_review]
Did you find this helpful?  [rev_helpful] of [rev_votes] Found Helpful
Reviewed by: (Verified Buyer)  from [user_city]. [user_email] on [review_date]
[rating]
Questions and Answers

Related Items

Recently Viewed Items